SIPLUS extreme products are based on Siemens Industry standard products. The contents listed here were taken from the respective standard products. SIPLUS extreme-specific information was added.
SIPLUS Y-Link for S7-400H | SIPLUS S7 BUS MODULE | |
|---|---|---|
Order No. | 6AG1 197-1LA11-4XA0 | 6AG1 654-7HY00-7XA0 |
Order No. based on | 6ES7 197-1LA11-0XA0 | 6ES7 654-7HY00-0XA0 |
Ambient temperature range | 0 °C to +60 °C | -25 °C to +70 °C |
Conformal coating | Coating of the printed circuit boards and the electronic components | |
Technical data | The technical data of the standard product applies except for the environmental conditions. | |
Environmental conditions | ||
Relative humidity | 5 ... 100 % | |
Biologically active substances | Conformity with EN 60721‑3‑3, Class 3B2 mold and fungal spores (except fauna) | |
Chemically active substances | Conformity with EN 60721‑3‑3, Class 3C4 incl. salt mist and ISA–S71.04 severity level G1; G2; G3; GX 1)2) | |
Mechanically active substances | Conformity with EN 60721‑3‑3, Class 3S4 including conductive sand, dust 2) | |
Air pressure (depending on the highest positive temperature range specified) | 1080 ... 795 hPa (-1000 ... +2000 m) 795 ... 658 hPa (+2000 ... +3500 m) 658 ... 540 hPa (+3500 ... +5000 m) | |
1) ISA-S71.04 severity level GX: Long-term load: SO2 < 4.8 ppm; H2S < 9.9 ppm; Cl < 0.2 ppm; HCl < 0.66 ppm; HF < 0.12 ppm; NH < 49 ppm; O3 < 0.1 ppm; NOX < 5.2 ppm
Limit value (max. 30 min/d): SO2 < 17.8 ppm; H2S < 49.7 ppm; Cl < 1.0 ppm; HCl < 3.3 ppm; HF < 2.4 ppm; NH < 247 ppm; O3 < 1.0 ppm; NOX < 10.4 ppm
2) The supplied plug covers must remain in place over the unused interface when operated in atmospheres containing corrosive gases!
The technical documentation on SIPLUS can be found here:
http://www.siemens.de/siplus-extreme
The Y-Link is a transceiver for the transition from a redundant PROFIBUS master system to a single-channel PROFIBUS DP master system. It is used to connect devices with a single PROFIBUS DP interface as switched I/O to S7-400H.
The Y-Link comprises:
Snapped on mounting rails for setup with active bus modules.
A redundant PROFIBUS DP master system can be extended by means of Y-Links in the following way:
Y-Link
Y-Coupler
The Y-Link maps the lower-level DP master system on the redundant PROFIBUS DP master system as a switched PROFIBUS DP slave .
The Y-Coupler and the lower-level DP master system form an independent bus system and operate decoupled from the redundant bus system.
The Y-Link as a DP slave on the redundant DP master system acts as a proxy for the stations on the lower-level DP master system with regard to data.
The Y-Link can be configured with STEP 7 as of Version 5.2. It is not necessary to configure the Y-Coupler.
When STEP 7 calculates the bus parameters, the stations connected on the lower-level DP master system as well as the Y-Link itself are taken into account.
Parameter assignment for the DP slaves
The redundant DP master system assigns the parameters for the DP slaves in the lower-level DP master system via the Y-Link.
| 6ES7 153-2BA02-0XB0 |
General information |
|
Vendor identification (VendorID) | 801Eh |
Supply voltage |
|
24 V DC | Yes |
permissible range, lower limit (DC) | 20.4 V |
permissible range, upper limit (DC) | 28.8 V |
permissible range (ripple included), lower limit (DC) | 20.4 V |
permissible range (ripple included), upper limit (DC) | 28.8 V |
External protection for supply cables (recommendation) | 2.5 A |
Mains buffering |
|
| 5 ms |
Input current |
|
Current consumption, max. | 600 mA |
Rated value at 24 V DC | 650 mA |
Inrush current, typ. | 3 A |
I²t | 0.1 A²·s |
Output voltage |
|
Rated value, 5 V DC | Yes |
Output current |
|
for backplane bus (5 V DC), max. | 1.5 A |
Power losses |
|
Power loss, typ. | 5.5 W |
Address area |
|
Addressing volume |
|
| 244 byte |
| 244 byte |
Hardware configuration |
|
Number of modules per DP slave interface, max. | 12 |
Time stamping |
|
Accuracy | 1 ms; 1ms at up to 8 modules; 10ms at up to 12 modules |
Number of message buffers | 15 |
Messages per message buffer | 20 |
Number of stampable digital inputs, max. | 128; Max. 128 signals/station; max. 32 signals/slot |
Time format | RFC 1119 |
Time resolution | 0.466 ns |
Time interval for transmitting the message buffer if a message is present | 1 000 ms |
Time stamp on signal change | rising / falling edge as signal entering or exiting |
Interfaces |
|
Interface physics, RS 485 | Yes |
Interface physics, FOC | No |
PROFIBUS DP |
|
| 1 to 125 permitted |
| Yes |
| 70 mA |
| RS 485 |
| 12 Mbit/s |
| Yes |
| Yes |
| Yes; Sender |
| 9-pin sub D |
1st interface |
|
DP slave |
|
| SI04801.GSG |
| Yes |
Communication functions |
|
Bus protocol/transmission protocol | PROFIBUS DP to EN 50170 |
Isolation |
|
Isolation checked with | Isolation voltage 500 V |
Ambient conditions |
|
Operating temperature |
|
| 0 °C |
| 60 °C |
Air pressure |
|
| 3 000 m |
Degree and class of protection |
|
IP20 | Yes |
Configuration |
|
Configuration software |
|
| Yes; STEP 7 / COM PROFIBUS / non-Siemens tools via GSD file |
Dimensions |
|
Width | 40 mm |
Height | 125 mm |
Depth | 117 mm |
Weight |
|
Weight, approx. | 360 g |
| 6ES7 197-1LB00-0XA0 |
General system features |
|
Requirements for DP master system |
|
| 244 byte |
Supply voltage |
|
Description | via bus module |
permissible range, lower limit (DC) | 20.4 V |
permissible range, upper limit (DC) | 28.8 V |
Interfaces |
|
PROFIBUS DP |
|
|
|
| 12 Mbit/s; 45.45 kbit/s to 12 Mbit/s |
| Active terminating resistor (Bus Terminator) |
| Yes |
| 9 |
| 31; 64 when using RS 485 repeaters or OLM/OBT |
Protocols |
|
Further protocols |
|
| Yes |
Interrupts/diagnostics/status information |
|
Status indicator | No |
Alarms |
|
| No |
Diagnoses |
|
| Yes |
Galvanic isolation |
|
to lower-level DP master system | Yes |
Dimensions |
|
Width | 40 mm |
Height | 125 mm |
Depth | 130 mm |
Weight |
|
Weight, approx. | 200 g |
| Код | Заказной номер | Описание | Вес (кг) | Заказать |
|---|---|---|---|---|
| 108998 | 6AG1197-1LA11-4XA0 | siplus s7-400, y-link для подключения одноканальных слейвов к s7-400h для тяжёлых условий применения, основе 6es7197-1la11-0xa0 | 1.1 | Заказать |
| 109145 | 6AG1654-7HY00-7XA0 | siplus s7, шинный модуль для y-соединителя; расширенный диапазон рабочих температур -25... +70 градусов цельсия, на основе | 0.247 | Заказать |
| 110492 | 6ES7153-2BA02-0XB0 | simatic dp, интерфейсный модуль с улучшенными характеристиками im 153-2 high feature для et 200m, макс. 12 модулей s7-300, поддержка резервирования, временные метки для изохронного режима, спец.функции: 12 модулей, активный slave для коммутаторов и приво | 0.289 | Заказать |
| 110493 | 6ES7153-2BA82-0XB0 | simatic dp, интерфейсный модуль с улучшенными характеристиками im 153-2 high feature для et 200m, расширенный температурный диапазон, макс. 12 модулей s7-300, поддержка резервирования, временные метки для изохронного режима, спец.функции: 12 модулей, ак | 0.289 | Заказать |
| 110595 | 6ES7195-1GA00-0XA0 | simatic dp, et 200m, профильная шина длиной 483 mm, для установки до 5 активных шинных модулей, поддерживающих функции "горячей" замены модулей ввода-вывода | 1.215 | Заказать |
| 110596 | 6ES7195-1GF30-0XA0 | simatic dp, et 200m, профильная шина длиной 530 mm, для установки до 5 активных шинных модулей, поддерживающих функции "горячей" замены модулей ввода-вывода | 1.331 | Заказать |
| 62154 | 6ES7195-7HD10-0XA0 | simatic dp, et 200m, активный шинный модуль с поддержкой функций "горячей" замены, для установки 2 интерфейсных модулей im153-2 high future (fo) с поддержкой функций работы в резервированных сетях profibus | 0.126 | Заказать |
| 62157 | 6ES7197-1LB00-0XA0 | simatic s7, y-соединитель для блока y-образного подключения 1-канальных ведомых dp-устройств к резервированной сети profibus-dp | 0.252 | Заказать |
| 62464 | 6ES7654-7HY00-0XA0 | simatic s7, модуль внутренней шины для установки y-соединителя, с защитной крышкой | 0.1 | Заказать |
